Field Reference — Not Engineering Authority
Last reviewed November 2026 · IronWorker Pro v4.0
IronWorker Pro is a field reference tool. The settings, temperatures, procedures, electrode and gas selections, weld-test criteria, heat-input results, rigging/sling load values, calculator results, cut lists, takeoffs, plate nests, DXF parts, material orders, steel weights, rebar weld sizes, checklists, bolting, anchor/stud data, drill speeds, and grinding/abrasive guidance in this app are general starting points based on common industry practice. They are not a substitute for the items below, and the user is responsible for checking every result against approved sources before it is relied on.
Always Defer To
Welding
The governing welding code
AWS D1.1, D1.4, D1.5, D1.6, D1.8, ASME, or whatever governs your work
Your approved WPS
Your employer's or engineer's Welding Procedure Specification
Manufacturer data
Filler metal and equipment data sheets
The maker's data sheet & your WPS for field wire
Field wire settings are the maker's typical operating procedures (for Innershield NR-232, Lincoln Electric data sheet C3.2000.12), not a qualified procedure. Wire feed speed, voltage, stickout and polarity are essential variables: your WPS sets them, and it governs where it differs. Confirm the diameter and classification on the spool label, and check that the wire is approved for your job. For seismic (AWS D1.8) work, the project's filler metal requirements and your QC program decide what can be used.
A qualified professional
A welding engineer, CWI, or your Authority Having Jurisdiction (AHJ)
Your WPS for heat input
The heat-input calculator is a planning aid. Actual heat-input limits, ranges, and the arc-efficiency factor that applies come from your approved WPS and the governing code. Exceeding heat input can ruin the steel's mechanical properties — weld to the procedure, not the app. The same goes for heat straightening and cambering: temperature limits (commonly ~1200°F for structural grades) come from the engineer and the spec, not from glow color alone.
Your WPS for saved presets
Weld machine presets are your own notes. Re-check them against the approved WPS whenever the job, base metal, thickness, position, wire, gas, or machine changes.
AWS D1.4 & the engineer for rebar welds
Rebar weld sizes show the effective throat of flare-bevel and flare-V welds and the minimum length per AWS D1.4/D1.4M:2018. The required weld length, whether a bar can be welded at all (A706 vs. A615 and its carbon equivalent), and preheat are set by the engineer, the approved WPS, and the code. Never weld crossing bars or substitute bars without written approval.
The test facility & your qualification paperwork
Weld test guidance here is general preparation only. The testing facility, the governing code, and the employer set the coupon, position, acceptance criteria, and what your qualification actually covers. Your WPQ document — not a rule of thumb — states the positions and thicknesses you are qualified for, and qualifications expire or lapse under code rules.
The laser safety program & your LSO
Laser welding is a different hazard class than arc welding. A welding hood offers no protection — you need eyewear rated for that machine's wavelength, plus enclosures, interlocks, and documented training. Class 4 laser work requires a laser safety program and a designated Laser Safety Officer under ANSI Z136.1. Never operate or stand near an operating laser without that program in place.
Rigging, Cranes & Fall Protection
The sling tag & your rigger/foreman
For ANY lift: the working load limit on the physical sling tag is the authority — never the app. Confirm every pick with your foreman, a qualified rigger, or competent person. No legible tag = the sling is out of service. Follow OSHA & ASME B30.9.
One qualified signalperson & the crane operator
The crane hand-signal guide is a study aid showing the standard signals. On the job, only one qualified signalperson directs the crane — except STOP and EMERGENCY STOP, which anyone gives and the operator must obey. Follow ASME B30.5, OSHA, and your site's crane-safety and signaling procedures.
The site lift procedure, not this worksheet
The Lift Plan tool adds up weights and compares them to the chart number you type in. It does not read a load chart, check the crane configuration, or approve a lift. The operator, the chart in the cab, and your site's lift and critical-lift procedures govern every pick.
The crane operator & the lift plan
Load chart material here is educational. Only the chart in that specific machine, in that exact configuration, read by a qualified operator, governs a lift. Anyone may stop a lift they believe is unsafe.
Your competent person & the equipment manual
Fall clearance figures are planning aids only. Every harness, lanyard, and SRL has manufacturer-published clearance requirements — those govern, not this app. Fall protection systems must be selected and planned under OSHA 1926 Subpart M by a qualified person, and rescue must be planned before anyone ties off.
Calculators, Bolting & Shop Work
The drawings, specs & a competent person
For calculator results, bolting, stud/anchor layout, and member sizes: verify against the approved drawings and project specs, and confirm with your foreman, detailer, or engineer. Double-check every measurement — a calculator can only work with what you type in.
Your layout on the steel
Equal Spacing, Arc Radius and Bolt Circle round each answer to the nearest 1/16″ (spacing marks are each measured from the start, so rounding doesn't stack up). The tape readout shows the same rounded number. Bolt circle X/Y is measured from the center with the first hole at the angle you enter. Lay out and check on the actual piece against the shop drawings before you cut, drill or weld.
The shop drawings for copes, holes & deck
Cope and hole layout results are a check against the shop drawings, never a replacement for them — the engineer checks coped-beam strength, and connection details come from the drawings. The deck estimator counts sheets, fasteners and studs for ordering; the fastening pattern and stud layout come from the deck and structural drawings.
The shop drawings & your tape
Cut Pro and the Cut Optimizer only know the stock lengths, kerf, and piece lengths you type in. Check every cut against the approved drawings, allow for squaring the ends and bad stock, and measure before you cut. Steel weights and shape dimensions are nominal — real weights vary with mill tolerance, so add rigging weight and verify before any pick.
The bolting spec & RCSC
Bolt tension and torque figures are reference starting points. Structural bolting is installed and inspected to the RCSC Specification and the engineer's requirements — verified by tension (turn-of-nut, DTI, or tension-control bolts), not by a torque wrench alone. Torque varies with lube and thread condition. Follow the approved bolting procedure and your inspector.
The disc label & your safety officer
For grinding, cutting & abrasive work: the max RPM and ratings stamped on the disc are the authority — never exceed them. Match the disc to your grinder and the material, inspect before use, keep the guard on, and follow your employer's safety program and the manufacturer's instructions.
Shop Tools: Takeoff, Nesting, Part Maker & Orders
The approved drawings for every takeoff
Steel Takeoff reads the sizes printed on a PDF and measures the lines it finds at the sheet scale. A wrong scale, a member drawn oddly, sizes that only appear in schedules or details, and connection material are yours to check. A takeoff is an estimate for bidding and ordering, not a bill of materials. Check every quantity against the approved drawings before you bid or order.
Your nesting software & your tape
Plasma Nest and Cut Pro lay parts out as rectangles to count sheets and sticks. Your table's own nesting software (such as ProNest) sets the real cut path, lead-ins and spacing, and round or odd-shaped parts can nest tighter there. Check the layout before you burn and the cut sheet before you saw.
The shop drawing for every DXF
Part Maker builds DXF files from the sizes you type. Check each part (size, holes, slots and scribe marks) against the approved shop drawing before it goes on the table, and run a test piece after any change to your marking setup. Scribe marks show where studs, anchors and lines go; the drawing and your own layout check decide where they belong.
Your supplier's confirmation
A material order from Cut Pro lists what you entered. Stock lengths, grades, availability, weights and prices are set by your supplier, so confirm the order and request mill certs from them. Weights shown are nominal.
Checklists, Training & Diagrams
Your permit, JHA & the site's procedures
The Job Checklists (Pre-Lift, Fall Protection, Hot Work) are memory aids, not permits. They do not replace a hot-work permit, a pre-task plan or JHA, a lift plan, or your site's own forms. A signed checklist in your Job Log is your own record — not an inspection, an approval, or proof of compliance.
Your site orientation & safety training
Career, tool, and jobsite guidance in this app is general orientation for people new to the trade — it is not a substitute for site-specific training, your employer's safety program, OSHA 1926, or your competent person. Where anything here differs from what you were trained on site, the site governs. Practices and terminology also vary by region, local, and contractor.
Animated diagrams are teaching aids
The Visual tab shows simplified, not-to-scale illustrations and 3D views of welding, cutting, heat, rigging, and erection concepts. They omit PPE, fire watch, ventilation, and site-specific requirements for clarity. They are never a procedure — real work follows your WPS, rigging plan, hot-work permit, and employer safety program.
Your Data
QR codes & photo markup
A QR code carries the text itself — anyone who scans it can read it, so don't put anything private in it. Photo markup is your own note on your own photo; it is not an inspection report.
Your own backups
The Job Log, hours, photos, notes, favorites and presets live on this device. Sign in under Settings → Account to back them up to your IronWorker Pro account and restore them on another phone or computer; automatic backup keeps that copy current. If you don't sign in, nothing leaves the device, and deleting the app or clearing browser data erases it. Save Backup in the Job Log still makes a file you keep yourself.
Notes you write
Notes and checklists are saved on this device. When you're signed in, they also sync to your account so the same notes show on your other phone and on ironworkerpro.com; a note deleted on one device is deleted on the others. Don't keep passwords, ID numbers or bank details in Notes. Notes are your own reminders, not a permit, inspection record or sign-off.
Your iPhone app purchase & the website
When you sign in inside the iPhone app, the app sends ironworkerpro.com Apple's signed record that this Apple ID bought IronWorker Pro (no card or Apple ID details). The website checks Apple's signature and turns on Pro Tools for the account you signed in with. One App Store purchase can unlock up to two website accounts. Android purchases aren't linked yet.
Your account & saved projects
A free account stores your app backups and the projects you save in Cut Pro, Part Maker, Plasma Nest and Steel Takeoff on IronWorker Pro's server, so you can open them anywhere you sign in. In the app, Cut Pro needs a sign-in; once you have signed in on a phone, it also works there without signal. On ironworkerpro.com, Cut Pro is part of Pro Tools and needs Pro (a purchase, an access code, or the iPhone app purchase below). Sign-in is handled by Google Firebase. Your data isn't sold or shown to other users; a shop job board is seen only by the people in that group. To delete your account and saved data, ask through Feedback in the app. Keep your own copy of anything you can't afford to lose.
Why this matters: Welding parameters depend on machine, joint, position, base metal, thickness, and conditions no general reference can account for. Always verify against the code edition named in your contract documents and your approved procedures before production welding. When in doubt, follow the code and your engineer.
⚠ Rigging is life-safety. The sling load values in this app are typical reference figures only — actual capacity depends on the sling's maker, grade, construction, condition, hitch, and angle, and is stated on the physical tag. A dropped or shifted load can kill. Never rig from this app alone: read the tag, inspect the sling, calculate the angle, and confirm the lift with your foreman or a qualified rigger. When in doubt, do not lift.
⚠ Grinding & abrasive wheels can kill. An over-speed or cracked disc can shatter at thousands of RPM. The disc's max RPM and ratings are stamped on it — your grinder must never exceed them. Inspect every disc, ring-test bonded wheels, keep the guard on, match the disc to the material, never side-load a cut-off wheel, and wear a face shield. Follow your employer's safety program and the manufacturer's instructions — the grinding guide here is general reference only.
References & Sources
All content is original work, organized from field experience and informed by widely published industry standards and manufacturer practice:
AWS D1.1/D1.1M:2025Structural Welding Code — Steel
AWS D1.4/D1.4M:2018Structural Welding Code — Steel Reinforcing Bars (with Amendment 1)
AWS D1.5M/D1.5:2025Bridge Welding Code (AASHTO/AWS)
AWS D1.8/D1.8M:2025Structural Welding Code — Seismic Supplement
AWS A2.4:2020Symbols for Welding, Brazing & Nondestructive Examination
AWS B5.1 / QC1Welder & inspector qualification — testing and certification
ASME B30.9-2025 / OSHA 1926.251Slings — working load limits, inspection & safe use
ASME B30.26Rigging hardware — shackles, clips, hooks & links
ASME B30.5-2025 / OSHA 1926 Subpart CCMobile cranes — signals, load charts & power-line clearance (1926.1408)
RCSC Specification (2020)Structural joints using high-strength bolts — pretension & installation
AISC 360-22Specification for Structural Steel Buildings — hole sizes, edge distance & spacing
ASTM A615 / A706Reinforcing bar grades — A706 is the weldable grade
OSHA 1926 Subpart MFall protection — 6 ft rule & system criteria (1926.502)
OSHA 1926 Subpart RSteel erection — structural steel assembly & safety
OSHA 1926 Subpart J / NFPA 51B:2024Welding, cutting & hot work — fire watch & permits
OSHA 1926.303 / ANSI B7.1Abrasive wheels & grinding — guarding and safe use
ANSI Z136.1-2022Safe use of lasers — laser welding hazard controls
AISC Shapes Database v16.0Steel shape dimensions & weights per foot
ASTM A992 / A500 / A53 / A36Wide-flange, HSS, pipe, plate & bar grades shown on material orders
AWS A5.20 / A5.36Flux-cored electrode classifications (E71T-8 self-shielded)
Lincoln Electric NR-232 data sheetInnershield NR-232, publication C3.2000.12 (05/2020) — typical operating procedures
Manufacturer guidesLincoln Electric, Miller, Hobart — typical parameter ranges
This app does not reproduce any copyrighted code text, tables, or figures. All diagrams, explanations, and data presentations are original. Code references are listed so you can consult the authoritative source directly. Editions shown were current as of October 2026; codes are revised every few years, and your project may be built to an earlier edition — the edition named in your contract documents or adopted by your jurisdiction governs. Obtain the official standards from AWS, ASME, AISC, RCSC, ANSI, ASTM, NFPA, and OSHA for authoritative requirements.
© 2026 Antonio Pebworth — IronWorker Pro. All rights reserved.